set ip route 0.0.0.0/0.0.0.0         10.1.1.1      
 !
 #syslog
 set logging console disable
 !
 #set boot command
 set boot config-register 0x2102
 set boot system flash bootflash:cat6000-supcv.5-4-3.bin
 !
 #port channel
 set port channel 2/7-8,3/7-8 428
 !
 # default port status is enable
 !
 !
 #module 1 : 2-port 1000BaseX Supervisor
 !
 #module 2 : 8-port 1000BaseX Ethernet
 set port name       2/7  Cat6506-02
 set port name       2/8  Cat6506-02
 set trunk 2/7  desirable isl 1-1005
 set trunk 2/8  desirable isl 1-1005
 set port channel 2/7-8 mode on
 !
 #module 3 : 8-port 1000BaseX Ethernet
 set port name       3/7  Cat6506-02
 set port name       3/8  Cat6506-02
 set trunk 3/7  desirable isl 1-1005
 set trunk 3/8  desirable isl 1-1005
 set port channel 3/7-8 mode on
 !
 #module 4 : 8-port 1000BaseX Ethernet
 set vlan 15   4/1
 !
 #module 5 : 8-port 1000BaseX Ethernet
 set vlan 15   5/1
 !
 #module 6 : 48-port 10/100BaseTX Ethernet
 !
 #module 15 : 1-port Multilayer Switch Feature Card
 !
 #module 16 empty
 end
 6506-01> (enable)
Catalyst 6506-02 配置
6506-02> (enable) show config
 This command shows non-default configurations only.
 Use ''show config all'' to show both default and non-default configurations.
 .........
 ................
 ..
 
 begin
 !
 # ***** NON-DEFAULT CONFIGURATION *****
 !
 !
 #time: Fri Jun 23 2000, 13:07:49
 !
 #version 5.4(3)
 !
 !
 #system web interface version Engine: 5.1 ADP device: Cat6000 ADP Version: 1.2
 ADK: 31
 !
 set password $2$JYD3$CcHOBhHYnLzI9O0B9F1Ov/
 set enablepass $2$93UN$/2fd2eCwlRdUSkklJ/KZ21
 !
 #system
 set system name  6506-02
 set system location Core-MDF-10
 set system contact  sysadmin@corp.com
 !
 #!
 #vtp
 set vtp domain Core-Domain
 set vlan 1 name default type ethernet mtu 1500 said 100001 state active
 set vlan 10 name Aggregation-10.10.0.0/16-Even type ethernet mtu 1500 said
 100010 state active
 set vlan 15 name Aggregation-10.10.0.0/16-Odd type ethernet mtu 1500 said
 100015 state active
 set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active
 set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state
 active stp ieee
 set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active
 stp ibm
 set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state
 active mode srb aremaxhop 7 stemaxhop 7 backupcrf off
 !
 #ip
 set interface sc0 1 10.1.1.5/255.255.255.0 10.1.1.255
        
 set ip route 0.0.0.0/0.0.0.0         10.1.1.1      
 !
 #syslog
 set logging console disable
 !
 #set boot command
 set boot config-register 0x2102
 set boot system flash bootflash:cat6000-supcv.5-4-3.bin
 !
 #port channel
 set port channel 2/7-8,3/7-8 448
 !
 # default port status is enable
 !
 !
 #module 1 : 2-port 1000BaseX Supervisor
 !
 #module 2 : 8-port 1000BaseX Ethernet
 set port name       2/7  Cat6506-01
 set port name       2/8  Cat6506-01
 set trunk 2/7  desirable isl 1-1005
 set trunk 2/8  desirable isl 1-1005
 set port channel 2/7-8 mode on
 !
 #module 3 : 8-port 1000BaseX Ethernet
 set port name       3/7  Cat6506-01
 set port name       3/8  Cat6506-01
 set trunk 3/7  desirable isl 1-1005
 set trunk 3/8  desirable isl 1-1005
 set port channel 3/7-8 mode on
 !
 #module 4 : 8-port 1000BaseX Ethernet
 set vlan 10   4/1
 !
 #module 5 : 8-port 1000BaseX Ethernet
 set vlan 10   5/1
 !
 #module 6 : 48-port 10/100BaseTX Ethernet
 !
 #module 15 : 1-port Multilayer Switch Feature Card
 !
 #module 16 empty
 end
 6506-02> (enable)

转载地址：http://www.net130.com/CMS/Pub/Tech/tech_config/92840.htm